[2022] NACE-CIP2-001 by CIP Level 2 Actual Free Exam Practice Test [Q47-Q61]

Rate this post

[2022] NACE-CIP2-001 by CIP Level 2 Actual Free Exam Practice Test

Free CIP Level 2 NACE-CIP2-001 Exam Question

NEW QUESTION 47
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be

washed with clean potable water prior to Use.

mixed with uncontaminated abrasive

run through the air wash separator.

disposed of properly.

NEW QUESTION 48
External coatings applied to buried pipelines are generally tested for:

Gloss level

Chalking resistance

Cathodic disbondment

Solvent resistance

NEW QUESTION 49
Ideally, documentation requirements should be defined:

At the pre-job conference

In the specification

By the inspector

By the contractor

NEW QUESTION 50
You should bulk store coatings containing isocyanates

in a well ventilated area separate from the work place.

in a heated warehouse.

in a refrigerated warehouses

wherever it is convenient

NEW QUESTION 51
The Inspectors’ goal at the Pre-Job Conference is to:

Obtain a clear understanding of the Specification

Discuss contractual requirements

Manage the meeting so it doesn’t go off topic

Take accurate meeting minutes for distribution

NEW QUESTION 52
The main reason dehumidification is used during coating operations is to

control the environment

reduce the possibility of missing the recoat window.

allow the contractor to guarantee the completion date.

avoid repetitive blasting/coating operations.

NEW QUESTION 53
In which type of concrete are laitance commonly encountered?

Concrete block (poured with a form)

Gunite

Glass fiber cement

Poured (wet cast)

NEW QUESTION 54
Non-Conformance Reports are designed to:

Punish the Contractor for substandard work

Elevate the status of the Inspector

Assist the Owner in negotiating credits from the Contractor

To identify items that do not meet the specification requirements

NEW QUESTION 55
When performing inspection in accordance with ASTM D 4138 the Inspector will use:

A set of 14 pencils of varying hardness

A destructive paint inspection Tooke gauge

A mechanical adhesion tester

A hardness tester

NEW QUESTION 56
The best choice of instrument for holiday testing of thick film concrete coatings is:

Low Voltage Sponge Type

High Voltage DC Pulse Type

High Voltage DC Constant Current

High Voltage AC

NEW QUESTION 57
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner’s representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?

SP 1 followed by acid etching

SP 1 followed by caustic etching

SP 1 followed by SP 2

SP 1 followed by SP 3

NEW QUESTION 58
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:

Magnetic coatings applied to a magnetic metallic substrate

Non-Conductive coatings applied to a conductive metallic substrate

Conductive coatings applied to a magnetic metallic substrate

Conductive coatings applied to a cementitious substrate

NEW QUESTION 59
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:

Correct the errors yourself and suggest the Level 1 inspector be replaced

Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent

Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation

Correct the errors yourself and submit the reports without any further action

NEW QUESTION 60
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:

Verbally challenge the NCR

Request a re-blast of the item in question

Consult your supervisor

Review the NCR with the other Inspector

NEW QUESTION 61
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:

Stop the job

Require the Applicator to remove the coating

Advise the Owner and write a Non-Conformance report

Ignore the situation

Loading …