JNCIS-SP JN0-363 Practice Test Engine Try These 265 Exam Questions [Q157-Q177]

QUESTION 157
Which statement is true when using MVRP on MX Series devices?

QUESTION 158
What is required on the egress and ingress devices to transport IPv6 traffic across an IPv4 network?

QUESTION 159
Referring to the exhibit, you have configured an aggregate route that represents the 172.21.0.0/24, 172.21.1.0/24, and 172.21.2.0/24 networks. However, when you view the routing table, your new route hidden.
Which action would you perform to determine the problem?

QUESTION 160
Click the Exhibit button.

Referring to the exhibit, how many milliseconds must pass before the interface ge-0/0/1.0 is considered down?

QUESTION 161
Before configuring an RSVP LSP in your network, you first apply a baseline configuration to all of the routers.Which three configuration elements are minimally required in the baseline? (Choose three.)

QUESTION 162
Click the Exhibit.


You are using OSPF as your IGP in your network. You have applied the OSPF configuration shown in the exhibit to router R1.
Which statement is true in this scenario?

QUESTION 163
Which three statements are true about GRES? (Choose three.)

QUESTION 164
You are deploying an RSVP-based MPLS network in your core. You must ensure that your LSPs are continually analyzing the usage levels and recalculating the best LSP. You also want to ensure that a minimal amount of traffic is lost when an LSP is re-signaled without user intervention.
Which two features must be enabled in this scenario? (Choose two.)

QUESTION 165
Click the Exhibit.

On an MX Series device, you must enable routing between VLANs 100,200, and the Internet ge-5/1/0, and ge-5/1/2 are bundled into interface ae3. Ge-5/1/4, and ge-5/1/5 are bundles into interface ae2. Both AE bundles trunk VLANs 100 and 200.
In this scenario, what is the correct configuration snippet for VLAN 100?

QUESTION 166
You are asked to configure an LSP which uses the OSPF link state database for path computations. Which two statements are correct in this scenario? (Choose two.)

QUESTION 167
In your RSVP network you have configured three separate LSPs to the same egress address. You have made no other configuration changes to the forwarding decisions made by the router.Which commands can you use to determine which LSP is being used to forward packets?

QUESTION 168
Click the exhibit.

You are asked to enable a new BGP connection on R1, which has an existing IPv4 peering with R2. The new peering with R3 will use IPv6.
Referring to the exhibit, which two steps are required to enable the new IPv6 peering? (Choose two.)

QUESTION 169
Click the Exhibit.

Your network consists of subnets shown in the exhibit. You are asked to create an aggregate route for Router 1.
What is the appropriate prefix for the aggregate route in this scenario?

QUESTION 170
You own a small company and need to assign IPv6 addresses to your routers. Because you want to follow the guidelines spelled out in RFC 3177, you want to design your network with the correct prefixes.Which prefix would your ISP likely allocate to your company?

QUESTION 171
Click the Exhibit.

The router with the configuration shown in the exhibit has two interfaces, both of which are operational and can pass traffic. These interfaces are connected to two different routers, both of which are configured for OSPF area 0.0.0.1. The router has received LSAs and can now send traffic into the backbone area.
Which two statements are correct? (Choose two.)

QUESTION 172
You want the R1 and R3 routers to forward traffic destined to the 203.0.113.0/24 network through R2. Which BGP attribute would you modify to satisfy this requirement?

QUESTION 173
Router A receives two similar route advertisements from different BGP peers.What would cause a route to be selected in this scenario?

QUESTION 174
Referring to the exhibit, which firewall filter action(s) will be applied to incoming frames to ge-1/0/3?

QUESTION 175
Click the Exhibit button.

Referring to the exhibit, which two statements are true? (Choose two.)

QUESTION 176
Click the Exhibit.


You have just configured a GRE tunnel, but you notice that the GRE tunnel is flapping.
Referring to the exhibit, which two would you take to solve this problem? (Choose two.)

QUESTION 177
You are setting up a new IS-IS adjacency between two devices. The new Level1 adjacency is not establishing.
What would cause this behavior?