[Q139-Q157] PassTestking JN0-363 Real Exam Question Answers Updated [May 16, 2024]

Rate this post

PassTestking JN0-363 Real Exam Question Answers Updated [May 16, 2024]

Easily To Pass New Juniper JN0-363 Dumps with 293 Questions

Juniper JN0-363 exam is designed for professionals who wish to gain extensive knowledge and skills in service provider routing and switching. It is also known as the Service Provider Routing and Switching, Specialist (JNCIS-SP) exam. JN0-363 exam is intended for individuals who have a minimum of two years of experience in networking technologies and want to enhance their skills and knowledge in a service provider environment. JN0-363 exam is one of the most popular and widely accepted certification exams in the networking world.

NEW QUESTION 139
All devices in the network are configured correctly and the path requirements are valid.
Referring to the exhibit, which two statements are correct? (Choose two.)

The primary LSP will be signaled, and its state will be up.

The secondary LSP will not be signaled, and its state will be down.

The secondary LSP will be signaled, and its state will be up.

The primary LSP will not be signaled, and its state will be down.

NEW QUESTION 140
Exhibit

You confirm that the R2 and R3 routers are receiving a BGP route to the 203.0.113.0/24 network, but both routers display the route as hidden. Referring to the exhibit, which two actions solve this problem? (Choose two.)

Apply the routing policy on R1 as an import policy to the IBGP group.

Configure a routing policy on R1 that sets the next hop for the 203 0.113.0/24 BGP route to the IP address that R1 uses for IBGP peering.

Configure a routing policy on R1 that sets the next hop for the 203.0.113.0/24 BGP route to the IP address that R1 uses for EBGP peering.

Apply the routing policy on R1 as an export policy to the IBGP group.

NEW QUESTION 141
You are implementing traffic engineering in your MPLS network. You must ensure that the MPLS routes are used to traverse your network. Your solution should not affect IGP routes in your route tables.
In this scenario, which traffic engineering setting will accomplish this behavior?

bgp-igp-both-ribs

mpls-forwarding

bgp-igp

bgp

NEW QUESTION 142
Referring to the exhibit, what must be included in the Route1 configuration when establishing an EBGP session with the ISP?

A local address must be specified.

A local AS must be specified.

The BGP session type internal must be specified.

The BGP session type external must be specified.

NEW QUESTION 143
Which statement is true regarding default MPLS label handling?

A router that pops a label from a label stack always pushes a new label on the packet

A router that pops a label from a label stack forwards a frame based on the label that was popped.

A router that pops a label from a label stack forwards a frame based on the underlying destination IP address.

A router that pops a label from a label stack applies class of service based on the IP header to ToS bits.

NEW QUESTION 144
You have been asked to identify what the contributing routes are for route 204.7.15/21.Which command will show this information?

show route 204.7.15/21

show route 204.7.15/21 extended

show route 204.7.15/21 exact summary

show route 204.7.15/21 detail

NEW QUESTION 145
Exhibit

Referring to the exhibit, what is the minimum number of LSPs required to support alt four networks?

NEW QUESTION 146
Referring to the exhibit, you have an established RSVP LSP between R1 and R4 when you experience a link failure between R2 and R3. Which two statements are correct? (Choose two.)

R2 sends a ResvTear message upstream to R1 signaling the link failure.

R3 sends a PathTear message downstream to R4 signaling the link failure.

R2 sends a PathTear message upstream to R1 signaling the link failure.

R3 sends a ResvTear message downstream to R4 signaling the link failure.

NEW QUESTION 147
Exhibit

You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.
What is the problem in this scenario?

This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

The family iso statement must be added to the logical interface.

The router at the other end of the link Is not sending any IS-IS Hello messages.

The router at the other end of the link is a Level 1 only router.

NEW QUESTION 148
Exhibit

Which prefix in the output shown in the exhibit is an external prefix injected by an OSPF router?

192.168.1.3

172.18.1.0/24

192.108.1.4

172.26.4.0730

NEW QUESTION 149
Which two statements are true about IP and GRE tunnels? (Choose two.)

The protocol field is changed in the inner IP packet header

Tunnel traffic is encrypted

The TTL field is changed in the inner IP packet header

Tunnel endpoints need a valid route to the remote endpoint

NEW QUESTION 150
Exhibit

Which prefix in the output shown in the exhibit is an external prefix injected by an OSPF router?

192.168.1.3

172.18.1.0/24

192.108.1.4

172.26.4.0730

NEW QUESTION 151
Click the Exhibit.

You have configured the IBGP group shown in the exhibit. However, committing your configuration fails.
Which parameter should you add to the IBGP group configuration to correct the problem?

Type external

Type internal

Export <policy name>

As -override

NEW QUESTION 152
You are asked to configure an LSP which uses the OSPF link state database for path computations. Which two statements are correct in this scenario? (Choose two.)

You must use the no-cspf parameter in the label-switched-path configuration.

Traffic engineering extensions ate enabled by default In OSPF.

Traffic engineering extensions are not enabled by default in OSPF.

You must use the policing parameter in the label-switched-path configuration.

NEW QUESTION 153
Exhibit

You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses.
Which two tasks will accomplish your objective? (Choose two.)

Issue the sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 command.

Under the [edit routing-options] hierarchy, configure a 32-bit router ID.

issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.

Under the [edit routing-options] hierarchy, configure a 128-bit router ID.

NEW QUESTION 154
Exhibit

Referring to the exhibit, what must be included in the Route1 configuration when establishing an EBGP session with the ISP?

A local address must be specified.

A local AS must be specified.

The BGP session type internal must be specified.

The BGP session type external must be specified.

NEW QUESTION 155
You want to share routes between two routing instances that you have configured?
What are two ways to accomplish this task? (Choose two.)

Use a non-forwarding instance.

Configure an instance import policy

Create a forwarding instance.

Use a RIB group.

NEW QUESTION 156
An IS-IS TLV includes which two attributes? (Choose two.)

Topology

Vector

Length

Value

NEW QUESTION 157
An OSPF router does not have a router ID configured. In this scenario, which statement is correct about the router ID?

The Junos OS will use the IP address assigned to the interface with the lowest MAC address.

A router ID will not be assigned until it is manually configured.