200-301 Exam Dumps Pass with Updated May-2022 Tests Dumps [Q67-Q88]

Rate this post

200-301 Exam Dumps Pass with Updated May-2022 Tests Dumps

200-301 exam questions for practice in 2022 Updated 545 Questions

NO.67 Which two pieces of information can you determine from the output of the show ntp status command? (Choose two)

whether the NTP peer is statically configured

the IP address of the peer to which the clock is synchronized

the configured NTP servers

whether the clock is synchronized

the NTP version number of the peer

Below is the output of the “show ntp status” command. From this output we learn that R1 has a stratum of 10 and it is getting clock from 10.1.2.1.

NO.68 Which two command sequences must be configured on a switch to establish a Layer 3 EtherChannel with an open-standard protocol? (Choose two.)

interface GigabitEthernet0/0/1
channel-group 10 mode auto

interface GigabitEthernet0/0/1
channel-group 10 mode on

interface port-channel 10
no switchport
ip address 172.16.0.1 255.255.255.0

interface GigabitEthernet0/0/1
channel-group 10 mode active

interface port-channel 10
switchport
switchport mode trunk

Section: Network Access

NO.69 Refer to the exhibit.

Only four switches are participating in the VLAN spanning-tree process.
Branch-1 priority 614440
Branch-2: priority 39082416
Branch-3: priority 0
Branch-4: root primary
Which switch becomes the permanent root bridge for VLAN 5?

Branch-1

Branch-2

Branch-3

Branch-4

NO.70 Drag and drop the functions from the left onto the correct network components on the right

NO.71 An email user has been lured into clicking a link in an email sent by their company’s security organization. The webpage that opens reports that it was safe but the link could have contained malicious code. Which type of security program is in place?

Physical access control

Social engineering attack

brute force attack

user awareness

This is a training program which simulates an attack, not a real attack (as it says “The webpage that opens reports that it was safe”) so we believed it should be called a “user awareness” program. Therefore the best answer here should be “user awareness”. This is the definition of “User awareness” from CCNA 200-301 Offical Cert Guide Book:
“User awareness: All users should be made aware of the need for data confidentiality to protect corporate information, as well as their own credentials and personal information. They should also be made aware of potential threats, schemes to mislead, and proper procedures to report security incidents. ” Note: Physical access control means infrastructure locations, such as network closets and data centers, should remain securely locked.

NO.72 Refer to the exhibit.

A packet is being sent across router R1 to host 172.16.0.14. What is the destination route for the packet?

209.165.200.254 via Serial0/0/1

209.165.200.254 via Serial0/0/0

209.165.200.246 via Serial0/1/0

209.165.200.250 via Serial0/0/0

NO.73 Refer to the exhibit.

Drag and drop the networking parameters from the left onto the correct values on the right.

Explanation

NIC vendor OUI -> 00:0C:22NIC MAC address -> 00:0C:22:83:79:A3default gateway -> 192.168.1.193host IP address -> 192.168.1.200subnet mask -> 255.255.255.192 The “ip route” and “ip addr show eth1” are Linux commands.+ “ip route”: display the routing table+ “ip addr show eth1”: get depth information (only on eth1 interface) about your network interfaces like IP Address, MAC Address information

NO.74 Refer to Exhibit. Which action do the switches take on the trunk link?

The trunk does not form and the ports go into an err-disabled status.

The trunk forms but the mismatched native VLANs are merged into a single broadcast domain.

The trunk does not form, but VLAN 99 and VLAN 999 are allowed to traverse the link.

The trunk forms but VLAN 99 and VLAN 999 are in a shutdown state.

The trunk still forms with mismatched native VLANs and the traffic can actually flow between mismatched switches. But it is absolutely necessary that the native VLANs on both ends of a trunk link match; otherwise a native VLAN mismatch occurs, causing the two VLANs to effectively merge. For example with the above configuration, SW1 would send untagged frames for VLAN
999. SW2 receives them but would think they are for VLAN 99 so we can say these two VLANs are merged.

NO.75 Drag and drop the Cisco Wireless LAN Controller security settings from the left onto the correct security mechanism categories on the right.

NO.76 Refer to the exhibit.

An engineer is tasked with verifying network configuration parameters on a client workstation to report back to the team lead. Drag and drop the node identifiers from the left onto the network parameters on the right.

NO.77 Drag and drop the SNMP manager and agent identifier commands from the left onto the functions on the right

NO.78 How does NAT overloading provide one-to-many address translation?

It uses a pool of addresses

It converts IPV4 addresses to unused IPv6 Addresses

It assigns a unique TCP/UDP port to each session

It uses virtual MAC Address and Virtual IP Addresses

NO.79 Refer to the exhibit. C-router is to be used as a “router-on-a-stick” to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?

These commands need to be added to the configuration:
C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0

These commands need to be added to the configuration:
C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0

These commands need to be added to the configuration:
C-router(config)# router rip
C-router(config-router)# network 172.19.0.0

No further routing configuration is required.

Section: IP Connectivity
Explanation:
Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLA will be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols need to be configured.

NO.80 Refer to the exhibit.

An engineer is tasked with verifying network configuration parameters on a client workstation to report back to the team lead. Drag and drop the node identifiers from the left onto the network parameters on the right.

NO.81 Which result occurs when PortFast is enabled on an interface that is connected to another switch?

Spanning tree may fail to detect a switching loop in the network that causes broadcast storms

VTP is allowed to propagate VLAN configuration information from switch to switch automatically.

Root port choice and spanning tree recalculation are accelerated when a switch link goes down

After spanning tree converges PortFast shuts down any port that receives BPDUs.

NO.82 Which VTP mode prevents you from making changes to vlans?

Server

Client

Transparent

Off

NO.83 Which feature on the Cisco Wireless LAN Controller when enabled restricts management access from specific networks?

CPU ACL

TACACS

Flex ACL

RADIUS

Reference: https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/71978-acl-wlc.html

NO.84 Refer to the exhibit.

What does router R1 use as its OSPF router-ID?

10.10.1.10

10.10.10.20

172.16.15.10

192.168.0.1

Explanation
OSPF uses the following criteria to select the router ID:1. Manual configuration of the router ID (via the
“router-id x.x.x.x” command under OSPF router configuration mode).2. Highest IP address on a loopback interface.3. Highest IP address on a non-loopback and active (no shutdown) interface.

NO.85 Which two steps must you perform on each device that is configured for IPv4 routing before you implement OSPFv3? (Choose two)

configure an autonomous system number

configure a loopback interface

configure a router ID

Enable IPv6 on an interface

Enable IPv6 unicast routing

NO.86 An engineer must configure a WLAN using the strongest encryption type for WPA2-PSK.
Which cipher fulfills the configuration requirement?

WEP

AES

RC4

TKIP

NO.87 Drag and drop the IPv4 network subnets from the left onto the correct usable host ranges on the right