Pass Cisco 300-410 Exam With Practice Test Questions Dumps Bundle [Q120-Q139]

Rate this post

Pass Cisco 300-410 Exam With Practice Test Questions Dumps Bundle

2022 Valid 300-410 test answers & Cisco Exam PDF

The Cisco 300-410 exam is all about the implementation of Cisco enterprise advanced routing and services. It also evaluates one’s knowledge and skills in troubleshooting routing services and technologies, infrastructure security, infrastructure automation, infrastructure services, VPN services, and Layer 3.

Q120. Refer to the exhibit.

An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?

Dynamic routing protocols always have priority over static routes.

The metric of the OSPF route is lower than the metric of the static route.

The configured AD for the static route is higher than the AD of OSPF.

The syntax of the static route is not valid, so the route is not considered.

Explanation
The AD of static route is manually configured to 130 which is higher than the AD of OSPF router which is
110.

Q121. Refer to the exhibit.

The administrator is trying to overwrite an existing file on the TFTP server that was previously uploaded by another router. However, the attempt to update the file fails. Which action resolves this issue?

Make the packages.conf file executable by all on the TFTP server

Make the packages.conf file writable by all on the TFTP server

Make sure to run the TFTP service on the TFTP server

Make the TFTP folder writable by all on the TFTP server

Q122. A network administrator cannot connect to a device via SSH. The line vty configuration is as follows:

Which action resolves this issue?

Increase the session timeout

Change the stopbits to 10.

Configure the transport input SSH

initialize the SSH key

Q123. Which values identifies VPNs in an EVN environment?

DLCI

Route target

Virtual network tag

VLAN ID

Explanation/Reference:
https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/layer-3-vpns-l3vpn/whitepaper_c11-
638769.html

Q124. Refer to the exhibit.

Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue?

Change the direction of the distribute-list command from out to in.

Remove the line with the sequence number 5 from the prefix list.

Remove the prefix keyword from the distribute-list command.

Remove the line with the sequence number 10 from the prefix list.

Q125. Which IGPs are supported by the MPLS LDP autoconfiguration feature?

RIPv2 and OSPF

OSPF and EIGRP

OSPF and ISIS

ISIS and RIPv2

Q126. Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.

Q127. Refer to the exhibit.

An engineer is troubleshooting a failed Telnet session from PC to the DHCP server. Which action resolves the issue?

Remove sequence 30 and add it back to the IPv6 traffic filter as sequence 5.

Remove sequence 20 and add it back to the IPv6 traffic filter as sequence 5.

Remove sequence 10 to add the PC source IP address and add it back as sequence 10.

Remove sequence 20 for sequence 40 in the access list to allow Telnet.

Q128.

Refer to the exhibit. A network administrator redistributed the default static route into OSPF toward all internal routers to reach to Internet. Which set of commands restores reachability to the Internet by internal routers?

router ospf 1
default-information originate

router ospf 1
network 0.0.0.0 0.0.0.0 area 0

router ospf 1
redistribute connected 0.0.0.0

router ospf 1
redistribute static subnets

Q129. Drag and drop the MPLS VPN device types from the left onto the definitions on the right.

Q130. Refer to the exhibit.

Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed

Q131. Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?

R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.

Route reflector setup requires full IBGP mesh between the routers.

In route reflector setup, only classful prefixes are advertised to other clients.

In route reflector setups, prefixes are not advertised from one client to another.

Section: Layer 3 Technologies
Explanation/Reference:

Q132. Refer to the exhibit.

After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-to-spoke and hub were not establishing. Which two actions resolved the issue? (Choose two.)

Configure the crypto isakmp key cisco address 0.0.0.0 on R2 and R3.

Remove the crypto isakmp key cisco address 10.1.1.1. on R2 and R3.

Change the mode from mode transport to mode tunnel on R2.

Configure the mode from mode tunnel to mode transport on R3.

Q133. Refer to the exhibit.

A router receiving BGP routing updates from multiple neighbors for routers in AS 690. What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.1.1?

The local preference value in another neighbor statement is higher than 250.

The local preference value should be set to the same value as the weight in the route map.

The route map is applied in the wrong direction.

The weight value in another statement is higher than 200.

Q134. Refer to the exhibit.

ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console. Which command is missing from the IP SLA configuration?

Start-time 00:00

Start-time 0

Start-time immediately

Start-time now

Q135. Refer to the exhibit.

Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed

Explanation
vty 0:
+ cisco
+ 0csic
vty 1:
+ no username
+ no password
The command “aaa authentication login default none” means no authentication is required when access to the device via Console/VTY/AUX so if one interface does not specify another login authentication method (via the “login authentication …” command), it will allow to access without requiring username or password. In this case VTY 1 does not specify another authentication login method so it will use the default method (which is “none” in this case).

Q136. Refer to the exhibit.
A network administrator configured an IPv6 access list to allow TCP return frame only, but it is not working as expected. Which changes resolve this issue?

Option A

Option B

Option C

Option D

Explanation
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750/software/release/122_55_se/configuration/

Q137. Which Ipv6 first-hop security feature helps to minimize denial of service attacks?

IPv6 Router Advertisement Guard

IPv6 Destination Guard

DHCPv6 Guard

IPv6 MAC address filtering

The Destination Guard feature helps in minimizing denial-of-service (DoS) attacks. It performs address resolutions only for those addresses that are active on the link,and requires the FHS binding table to be populated with the help of the IPv6 snooping feature.The feature enables the filtering of IPv6 traffic based on the destinationaddress, and blocks the NDP resolution for destination addresses that are not found in the binding table. By default, the policy drops traffic coming for an unknowndestination.

Q138. Refer to the exhibit.

The output of the trace from R5 shows a loop in the network. Which configuration prevents this loop?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

Q139. Refer to the exhibit.

During troubleshooting it was discovered that the device is not reachable using a secure web browser. What is needed to fix the problem?