[Q139-Q157] PassTestking JN0-363 Real Exam Question Answers Updated [May 16, 2024]

给本帖评分

PassTestking JN0-363 Real Exam Question Answers Updated [May 16, 2024]

Easily To Pass New Juniper JN0-363 Dumps with 293 Questions

Juniper JN0-363 exam is designed for professionals who wish to gain extensive knowledge and skills in service provider routing and switching. It is also known as the Service Provider Routing and Switching, Specialist (JNCIS-SP) exam. JN0-363 exam is intended for individuals who have a minimum of two years of experience in networking technologies and want to enhance their skills and knowledge in a service provider environment. JN0-363 exam is one of the most popular and widely accepted certification exams in the networking world.

新问题 139
All devices in the network are configured correctly and the path requirements are valid.
参考展品，哪两个说法是正确的？(请选择两项）。

The primary LSP will be signaled, and its state will be up.

The secondary LSP will not be signaled, and its state will be down.

The secondary LSP will be signaled, and its state will be up.

The primary LSP will not be signaled, and its state will be down.

新问题 140
展览

您确认 R2 和 R3 路由器接收到一条到 203.0.113.0/24 网络的 BGP 路由，但两台路由器都将该路由显示为隐藏路由。请参阅展品，哪两个操作可以解决这个问题？(选择两项）。

Apply the routing policy on R1 as an import policy to the IBGP group.

Configure a routing policy on R1 that sets the next hop for the 203 0.113.0/24 BGP route to the IP address that R1 uses for IBGP peering.

在 R1 上配置路由策略，将 203.0.113.0/24 BGP 路由的下一跳设置为 R1 用于 EBGP 对等互联的 IP 地址。

将 R1 上的路由策略作为导出策略应用到 IBGP 组。

新问题 141
You are implementing traffic engineering in your MPLS network. You must ensure that the MPLS routes are used to traverse your network. Your solution should not affect IGP routes in your route tables.
In this scenario, which traffic engineering setting will accomplish this behavior?

bgp-igp-both-ribs

mpls-forwarding

bgp-igp

bgp

新问题 142
Referring to the exhibit, what must be included in the Route1 configuration when establishing an EBGP session with the ISP?

A local address must be specified.

A local AS must be specified.

The BGP session type internal must be specified.

The BGP session type external must be specified.

新问题 143
Which statement is true regarding default MPLS label handling?

A router that pops a label from a label stack always pushes a new label on the packet

A router that pops a label from a label stack forwards a frame based on the label that was popped.

A router that pops a label from a label stack forwards a frame based on the underlying destination IP address.

A router that pops a label from a label stack applies class of service based on the IP header to ToS bits.

新问题 144
You have been asked to identify what the contributing routes are for route 204.7.15/21.Which command will show this information?

show route 204.7.15/21

show route 204.7.15/21 extended

show route 204.7.15/21 exact summary

show route 204.7.15/21 detail

新问题 145
展览

Referring to the exhibit, what is the minimum number of LSPs required to support alt four networks?

新问题 146
Referring to the exhibit, you have an established RSVP LSP between R1 and R4 when you experience a link failure between R2 and R3. Which two statements are correct? (Choose two.)

R2 向上游 R1 发送 ResvTear 报文，提示链路故障。

R3 向下游的 R4 发送 PathTear 报文，提示链路故障。

R2 向上游 R1 发送 PathTear 报文，提示链路故障。

R3 向下游的 R4 发送 ResvTear 报文，提示链路故障。

新问题 147
展览

You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.
What is the problem in this scenario?

This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

The family iso statement must be added to the logical interface.

The router at the other end of the link Is not sending any IS-IS Hello messages.

The router at the other end of the link is a Level 1 only router.

新问题 148
展览

Which prefix in the output shown in the exhibit is an external prefix injected by an OSPF router?

192.168.1.3

172.18.1.0/24

192.108.1.4

172.26.4.0730

新问题 149
Which two statements are true about IP and GRE tunnels? (Choose two.)

The protocol field is changed in the inner IP packet header

Tunnel traffic is encrypted

The TTL field is changed in the inner IP packet header

Tunnel endpoints need a valid route to the remote endpoint

新问题 150
展览

Which prefix in the output shown in the exhibit is an external prefix injected by an OSPF router?

192.168.1.3

172.18.1.0/24

192.108.1.4

172.26.4.0730

新问题 151
点击展览。

You have configured the IBGP group shown in the exhibit. However, committing your configuration fails.
Which parameter should you add to the IBGP group configuration to correct the problem?

Type external

Type internal

Export <policy name>

As -override

新问题 152
要求您配置一个使用 OSPF 链路状态数据库进行路径计算的 LSP。在这种情况下，哪两种说法是正确的？

必须在标签交换路径配置中使用 no-cspf 参数。

在 OSPF 中，默认情况下已启用流量工程扩展。

OSPF 默认不启用流量工程扩展。

必须在标签交换路径配置中使用警务参数。

新问题 153
展览

要求您使用 IPv6 地址在路由器 R1 和 R2 之间配置 OSPF。
哪两项任务可以实现你的目标？(选择两项）。

执行 sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 命令。

在 [edit routing-options] 层次结构下，配置 32 位路由器 ID。

执行 set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 命令。

在 [edit routing-options] 层次结构下，配置 128 位路由器 ID。

新问题 154
展览

Referring to the exhibit, what must be included in the Route1 configuration when establishing an EBGP session with the ISP?

A local address must be specified.

A local AS must be specified.

The BGP session type internal must be specified.

The BGP session type external must be specified.

NEW QUESTION 155
You want to share routes between two routing instances that you have configured?
What are two ways to accomplish this task? (Choose two.)

Use a non-forwarding instance.

Configure an instance import policy

Create a forwarding instance.

Use a RIB group.

NEW QUESTION 156
An IS-IS TLV includes which two attributes? (Choose two.)

Topology

Vector

长度

价值

NEW QUESTION 157
An OSPF router does not have a router ID configured. In this scenario, which statement is correct about the router ID?

The Junos OS will use the IP address assigned to the interface with the lowest MAC address.

A router ID will not be assigned until it is manually configured.