Home  >  FlashArray-Implementation-Specialist / Pure Storage

[2025] Use Valid FlashArray-Implementation-Specialist Exam – Actual Exam Question & Answer [Q18-Q39]

Rate this post

[2025] Use Valid FlashArray-Implementation-Specialist Exam – Actual Exam Question & Answer

Test Engine to Practice FlashArray-Implementation-Specialist Test Questions

Pure Storage FlashArray-Implementation-Specialist Exam Syllabus Topics:

Topic Details
Topic 1
  • Pre-Installation
  • Upgrade: This section of the exam measures the skills of Enterprise Infrastructure Technicians and covers all preparation activities before deploying or upgrading a Pure Storage FlashArray. It includes understanding environmental requirements, verifying prerequisites, checking compatibility, and validating system readiness through appropriate tools and documentation.
Topic 2
  • Upgrades: This section of the exam measures the skills of FlashArray Implementation Specialists and focuses on tasks involved in managing firmware and software upgrades. Candidates must demonstrate knowledge of upgrade planning, verification steps, and rollback procedures, ensuring that systems are updated with minimal disruption to service.
Topic 3
  • Installation: This section of the exam measures the skills of Enterprise Infrastructure Technicians and focuses on executing a successful installation of FlashArray systems. It tests the ability to perform physical setup, cabling, configuration of network settings, and the application of initial system configurations necessary for full deployment.
Topic 4
  • Post-Installation
  • Upgrade: This section of the exam measures the skills of FlashArray Implementation Specialists and evaluates how professionals confirm system functionality after installation or an upgrade. It involves validating connectivity, running health checks, confirming configurations, and ensuring that the deployment meets operational expectations.

 

NEW QUESTION 18
What is the rack unit height of a FlashArray//XL?

 
 
 

NEW QUESTION 19
When should a FlashArray support case be opened?

 
 
 

NEW QUESTION 20
In a situation where iSCSI cards need to be re-used during a controller upgrade, which is a valid transfer path?

 
 
 

NEW QUESTION 21
A customer has ordered several FlashArrays and wants to have ActiveCluster configured. What is the maximum quantity of arrays supported with ActiveCluster?

 
 
 

NEW QUESTION 22
What should an Implementation Engineer do when installing rails in a threaded-hole rack?

 
 
 

NEW QUESTION 23
What is the minimum AC voltage required to operate a FlashArray//X20R4 array?

 
 
 

NEW QUESTION 24
An Implementation Engineer is performing a capacity consolidation on an X50R3.
Which command is needed for the engineer to determine whether the customer’s FlashArray supports SAS Flash Modules?

 
 
 

NEW QUESTION 25
An Implementation Engineer performs a controller upgrade. What is the command to check I/O health?

 
 
 

NEW QUESTION 26
What hardware should the Implementation Engineer find in the upgrade kit in order to perform an //X to //XL NDU?

 
 
 

NEW QUESTION 27
Before installing array rails, where should the cage nuts be placed?

 
 
 

NEW QUESTION 28
An Implementation Engineer is scheduled to install a FlashArray and a DirectFlash Shelf (DFS).
What action should the Implementation Engineer perform?

 
 
 

NEW QUESTION 29
An Implementation Engineer is onsite to install a new DFM data pack (DP) to CH0.BAY10-CH0.BAY19 of a FlashArray.
After adding the drives to the chassis, which command should the Implementation Engineer run to verify if the new DP is in a wide write group?

 
 
 

NEW QUESTION 30
A FlashArray arrives with Purity 5.3.8 applied out of the factory. The account team requests that the array configured with Purity 6.1.21. Which steps should the Implementation Engineer select to meet this requirement?

 
 
 

NEW QUESTION 31
After running puredb run giveback –safe command once CT0 has been upgraded, how long should the Implementation Engineer wait before continuing with the controller upgrade?

 
 
 

NEW QUESTION 32
What command will view NVRAM install and update status?

 
 
 

NEW QUESTION 33
Support requests a powercycle on a newly-installed FlashArray. What is the correct way to perform this action?

 
 
 

NEW QUESTION 34
What command will view NVRAM install and update status?

 
 
 

NEW QUESTION 35
Which command should an Implementation Engineer use to allow Support access to an array?

 
 
 

NEW QUESTION 36
A customer wants to expand the capacity of their FlashArray//X10 from 5/5 to 11/11. Which is the correct action to take?

 
 
 

NEW QUESTION 37
A customer would like to reduce SafeMode settings for retention and eradication with their current policy.
How is authorization obtained to make the requested changes?

 
 
 

NEW QUESTION 38
A FlashArray//XR2/3 has an Ethernet mezzanine (EMEZZ), what are the interface names of the ports on the mezzanine?

 
 
 

NEW QUESTION 39
If drives need to be relocated within an array for an XFORM upgrade, when should this be completed?

 
 
 

FlashArray-Implementation-Specialist Actual Questions Answers PDF 100% Cover Real Exam Questions: https://www.passtestking.com/Pure-Storage/FlashArray-Implementation-Specialist-practice-exam-dumps.html

Related Links: www.stes.tyc.edu.tw www.stes.tyc.edu.tw www.stes.tyc.edu.tw www.stes.tyc.edu.tw www.stes.tyc.edu.tw www.stes.tyc.edu.tw

Categories:FlashArray-Implementation-Specialist​Pure Storage

Tags:

admin

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *

Enter the text from the image below
 

Post comment