[Q43-Q62] 2025 Verified JN0-363 dumps Q&As on your JNCIS-SP Exam Questions Certain Success!

Rate this post

2025 Verified JN0-363 dumps Q&As on your JNCIS-SP Exam Questions Certain Success!

JN0-363 Exam Dumps – 100% Marks In JN0-363 Exam!

The JN0-363 exam covers a wide range of topics, including network architecture, routing protocols, MPLS, BGP, OSPF, and VPN technologies. Candidates are expected to have a strong foundation in these areas and be able to apply their knowledge to real-world scenarios. JN0-363 exam is designed to test the candidate’s ability to deploy, configure, and troubleshoot Juniper Networks routers and switches in a service provider environment.

NO.43 You have a stub OSPF area running in your network. Your supervisor has asked you to build a virtual link across this area to connect new equipment acquired in a recent ISP acquisition.Which statement is correct about this scenario?

Type 5 LSAs would be blocked in a stub area.

Type 5 LSAs would carry external information across your transit area to the backbone.

Type 5 LSAs would be seen only in the newly attached area.

Type 5 LSAs would be converted to type 7 LSAs.

NO.44 Referring to the exhibit, which statement is true about VRRP?

VRRP communication between the two devices is not functioning correctly.

Both routers are in the same state because they have the same VRRP priority.

RRP Is functioning normally in active/active mode.

The routers should use different virtual IP addresses for VRRP to function correctly.

NO.45 Click the Exhibit button. In the exhibit, all routers are sending routes to Router B.Which routes will be advertised from Router B to Router E?

BGP routes learned from Router A only

BGP routes learned from Router D only

BGP routes learned from Routers A and C only

BGP routes learned from Routers A, C, and D only

NO.46 Click the Exhibit button. In the exhibit, all routers are sending routes to Router B

Which routes will be advertised from Router B to Router D?

BGP routes learned from Router A only

BGP routes learned from Router E only

BGP routes learned from Routers A and C only

BGP routes learned from Routers A, C and E only

NO.47 Which statement is true when using MVRP on MX Series devices?

MVRP works with MSTP and RSTP, but not VSTP

MVRP works with RSTP and VSTP, but not MSTP

MVRP works with MSTP and VSTP, but not RSTP

MVRP does not work with MSTP, RSTP, and VSTP

https://www.juniper.net/documentation/en_US/junos/topics/topic-map/mvrp.html

NO.48 Click the Exhibit button.

Referring to the exhibit, which statement is correct?

Interface ge-3/0/0.0 has a default metric of 10

Interface xe-0/0/0.0 can only form a single adjacency

Interface xe-0/0/0.0 has a default metric of 10

Interface ge-1/0/0.0 can only form a single adjacency

NO.49 Exhibit

You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses.
Which two tasks will accomplish your objective? (Choose two.)

Issue the sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 command.

Under the [edit routing-options] hierarchy, configure a 32-bit router ID.

issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.

Under the [edit routing-options] hierarchy, configure a 128-bit router ID.

NO.50 Interface ge-0/0/0.0 connecls yout network to your ISP. You want to advertise this interface address as an Internal route In OSPF without creating a neighbor with your ISP.
In this scenario, how is this task accomplished?

Remove interface ge-0/0/0.0 from OSPF.

Create a generated route for Interface ge-0/0/0.0.

Add ge-0/0/0.0 as a passive interface In OSPF.

Configure a static route for Interface ge-0/0/0.0.

When you want to advertise an interface in OSPF but not form an OSPF adjacency over that interface (for example, towards an ISP), you can configure the interface as passive. This will advertise the network on the interface in OSPF without sending OSPF hello packets or forming OSPF neighbor relationships on that interface.
Reference:
Juniper Networks Technical Documentation on OSPF
OSPF Configuration Guide – Juniper Networks

NO.51 Click the Exhibit.

You have configured the IBGP group shown in the exhibit. However, committing your configuration fails.
Which parameter should you add to the IBGP group configuration to correct the problem?

Type external

Type internal

Export <policy name>

As -override

NO.52 You are asked to configure an LSP which uses the OSPF link state database for path computations. Which two statements are correct in this scenario? (Choose two.)

You must use the no-cspf parameter in the label-switched-path configuration.

Traffic engineering extensions ate enabled by default In OSPF.

Traffic engineering extensions are not enabled by default in OSPF.

You must use the policing parameter in the label-switched-path configuration.

The no-cspf command will activate usage of OSPF DB https://www.juniper.net/documentation/us/en/software/junos/ospf/topics/topic-map/configuring-ospf-support-for-traffic-engineering.html Not enabled by default for ospf

NO.53 You are asked to configure filter-based forwarding on a Junos device.
Which two statements are correct in this scenario? (Choose two.)

You must create a routing policy.

You must create a route target.

You must create and apply a match filter.

You must create a routing instance.

Filter-based forwarding in Junos requires the creation of a routing policy to specify the match conditions and actions and the application of a match filter to classify traffic to use the policy.References:
Filter-Based Forwarding Overview, Juniper Networks Documentation
Example: Configuring Filter-Based Forwarding, Juniper Networks Documentation

NO.54 You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses.
Which two tasks will accomplish your objective? (Choose two.)

Issue the sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 command.

Under the [edit routing-options] hierarchy, configure a 32-bit router ID.

issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.

Under the [edit routing-options] hierarchy, configure a 128-bit router ID.

NO.55 Referring to the exhibit, which two statements are correct? (Choose two.)

Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0/1 unchanged.

Traffic ingressing ge-0/0/0 that is tagged will VLAN 100 will be dropped.

Traffic ingressing ge0/0/0 that Is tagged with VLAN 200 will egress ge-0/0/1 with an outer VLAN tag of 200.

Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0M with an outer VLAN tag of 200.

NO.56 Exhibit

You have an established LSP between your R1 and R5 devices using the configuration shown in the exhibit. You are asked to ensure that MPLS labels are used to forward traffic by all devices within the LSP.
Which action will accomplish this behavior?

Configure the ultimace-hop-popping statement under the R1_TO_R5 label switched path on R1.

Configure the explicit-null statement under the protocol mpls hierarchy on R1.

Delete the no-espf statement under the R1_TO_R5 label switched path on R1.

Configure the install statement under the R1_TO_R5 label switched path on R1.

https://www.juniper.net/documentation/us/en/software/junos/mpls/topics/ref/statement/install-edit-protocols-mpls.html

NO.57 You confirm that the R2 and R3 routers are receiving a BGP route to the 203.0.113.0/24 network, but both routers display the route as hidden. Referring to the exhibit, which two actions solve this problem? (Choose two.)

Apply the routing policy on R1 as an export policy to the IBGP group.

Apply the touting policy on R1 as an import policy to the IBGP group.

Configure a routing policy on R1 that sets the next hop for the 203.0.113.0/24 BGP route to the IP address that R1 uses for IBGP peering.

Configure a routing policy on R1 that sets the next hop for the 203.0.113.0/24 BGP route to the IP address that R1 uses for EBGP peering.

NO.58 Click the Exhibit.

Your network consists of subnets shown in the exhibit. You are asked to create an aggregate route for Router 1.
What is the appropriate prefix for the aggregate route in this scenario?

172.42.32.0/20

172.42.32.0/22

172.42.32.0/19

172.42.32.0/21

NO.59 Exhibit

You have an established LSP between your R1 and R5 devices using the configuration shown in the exhibit. You are asked to ensure that MPLS labels are used to forward traffic by all devices within the LSP.
Which action will accomplish this behavior?

Configure the ultimace-hop-popping statement under the R1_TO_R5 label switched path on R1.

Configure the explicit-null statement under the protocol mpls hierarchy on R1.

Delete the no-espf statement under the R1_TO_R5 label switched path on R1.

Configure the install statement under the R1_TO_R5 label switched path on R1.

The “ultimate-hop-popping” term refers to the action taken by the penultimate router in an LSP to remove the MPLS label before delivering the packet to the ultimate router, which is not desired here. Configuring the “explicit-null” statement causes the penultimate router to replace the top label with a label that has a value of 0, which instructs the ultimate router to perform a label lookup and preserve the label switching for the entire LSP.
Reference:
Juniper Networks documentation on MPLS: MPLS Applications User Guide for Routing Devices

NO.60 Which two statements are correct about the service provider MPLS network shown in the exhibit? (Choose two.)

R3 is considered a P router.

R3 is considered a PE router.

R3 is considered a transit router.

R3 is considered an ingress router.

NO.61 Referring to the exhibit, what is the minimum number of LSPs required to support alt four networks?

NO.62 Referring to the exhibit, which two additional steps should you lake to fully configure NSR? (Choose two.)

You should configure the max period for NSR precision timers.

You must configure GRES.

You must configure graceful restart.

You should configure commit synchronization.

Loading …

The JN0-363 exam covers a wide range of topics, including advanced routing protocols, MPLS, BGP, OSPF, and IS-IS, among others. JN0-363 exam also tests the candidate’s ability to configure, troubleshoot, and manage Juniper’s service provider routing and switching devices. The JN0-363 certification is a valuable asset for individuals who want to advance their careers in the networking industry, as it demonstrates their expertise in designing and implementing complex networks.

Pass Your JN0-363 Exam Easily With 100% Exam Passing Guarantee: https://www.passtestking.com/Juniper/JN0-363-practice-exam-dumps.html

Categories:JN0-363Juniper