JN0-363 Tested & Approved JNCIS-SP Study Materials [Q27-Q49]

QUESTION 27
You want to disable MAC learning only for interface ge-0/0/0.0 on an MX Series device.
Which syntax will accomplish this task?

QUESTION 28
Which two statements describe advantages of using BGP for VPLS signaling instead of LDP signaling? (Choose two.)

QUESTION 29
You are asked to create connections between routing instances on the same Junos device and route between the connected Instances. What are two ways to accomplish this task? (Choose two.)

QUESTION 30
Click the Exhibit button.

Referring to the exhibit, if there is a connection failure between router1 and router2, how much time will pass before the devices declare the BFD session dead?

QUESTION 31
Which new field is added to an IPv6 header as compared to IPv4?

QUESTION 32
Which BGP message type is used to re-advertise routes that have already been sent to a peer and acknowledged using TCP?

QUESTION 33
Click the Exhibit.


Referring to the exhibit, the GRE tunnel between R-1 and R2 allows connectivity between User-1 and Server-1. User-1 can communicate with Server-1 with packets that are up to 1448 bytes in size.
However, if the packet size is larger than 1448, User-1 cannot communicate with Server-1.
In this scenario, how do you solve the communication problem?

QUESTION 34
What is the correct order of BGP attributes for active route selection?

QUESTION 35
You must configure an MX Series device to receive and forward a mixture of single-tag and dual-tag frames on interface xe-0/0/0.
In this scenario what will accomplish goal?

QUESTION 36
Click the Exhibit button. You have two routers connected over a Gigabit Ethernet link as shown in the exhibit It is required that an IS-IS adjacency be established without the need for a designated intermediate system (DIS)

Which configuration statement entered on both routers will achieve this goal?

QUESTION 37
Click the Exhibit button. You configured an aggregated Ethernet bundle between R1 and R2. Unfortunately, the bundle is not working correctly.
Referring to the exhibit, which configuration change will solve this issue?

QUESTION 38
Exhibit

Referring to the exhibit, which two additional steps should you lake to fully configure NSR? (Choose two.)

QUESTION 39
Exhibit.

Referring to the exhibit, you have configured an aggregate route that represents the 172.21.0.0/24, 172.21.1.0/24, and 172.21.2.0/24 networks. However, when you view the routing table, your new route hidden.
Which action would you perform to determine the problem?

QUESTION 40
How does a Junos device learn about MAC addresses when II is first connected to an Ethernet LAN?

QUESTION 41
Click the Exhibit button. What does IS-IS/18 mean in the output displayed in the exhibit?

QUESTION 42
Exhibit

Which two statements are correct about the information shown in the exhibit? (Choose two.)

QUESTION 43
Click the Exhibit button.

Referring to the exhibit, which statement is correct?

QUESTION 44
Exhibit

You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses.
Which two tasks will accomplish your objective? (Choose two.)

QUESTION 45
Which two statements ate correct about the information shown in the exhibit? (Choose two.)

QUESTION 46
Referring to the exhibit, you have configured an aggregate route that represents the 172.21.0.0/24, 172.21.1.0/24, and 172.21.2.0/24 networks. However, when you view the routing table, your new route hidden.
Which action would you perform to determine the problem?

QUESTION 47
Click the Exhibit button.

All devices in the network are configured correctly and the path requirements are valid.
Referring to the exhibit, which two statements are correct? (Choose two.)

QUESTION 48
Click the Exhibit button.

All devices in the network are configured correctly and the path requirements are valid.
Referring to the exhibit, which two statements are correct? (Choose two.)

QUESTION 49
Click the Exhibit.

On an MX Series device, you must enable routing between VLANs 100,200, and the Internet ge-5/1/0, and ge-5/1/2 are bundled into interface ae3. Ge-5/1/4, and ge-5/1/5 are bundles into interface ae2. Both AE bundles trunk VLANs 100 and 200.
In this scenario, what is the correct configuration snippet for VLAN 100?